rimontaggio motore Mp600 del 74
-
- Apista apprendista
- Messaggi: 47
- Iscritto il: 16 novembre 2016, 0:47
- Ape owned: MPV2
Re: rimontaggio motore Mp600 del 74
Thanks for your photos.
I wrote a little confusion.
I know how its made the seal, but i don't know how They orientation in the crankcase.
Please look the video by link below
https://youtu.be/YTBIqL2WJmU
It's a pratical test that the engine have another way for The inlet air.
I wrote a little confusion.
I know how its made the seal, but i don't know how They orientation in the crankcase.
Please look the video by link below
https://youtu.be/YTBIqL2WJmU
It's a pratical test that the engine have another way for The inlet air.
- kjjohnson
- 1° Apista restauratore
- Messaggi: 6143
- Iscritto il: 3 dicembre 2007, 11:17
- Ape owned: MPR2
- Località: Bayfield, Ontario, Canada
- Contatta:
Re: rimontaggio motore Mp600 del 74
Look at the parts photo T.l and on the clutch side the bearing goes in first, then the split ring and then the oil seal. First seal I would look at is the one behind the cooling fan, it's the one that usually goes bad first. I'm wondering if the seal is gone between the crankcase halves but I can't tell from way over here, I'd prefer it on my test stand
we buy/restore/sell P501 and P601s and parts/manuals/handbooks
http://www.kjjohnson.ca/
http://www.kjjohnson.ca/
-
- Apista apprendista
- Messaggi: 47
- Iscritto il: 16 novembre 2016, 0:47
- Ape owned: MPV2
Re: rimontaggio motore Mp600 del 74
Hi Ken,
In this Long adverture, a new passage:
Yesterday, i had to Cut some trees so i put on it the gasoline that i used for Ape....
What's happened?
The engine start with High smoke and The carburation was very clean.
I couldn't Cut anything!
So, i made a new fuel mix from another tank... surprise!
The engine run Very Good with out smoke and carburation perfect!
Now i think that the gas station sold me no only gasoline but a mix gasoline + diesel!!!!
In this Long adverture, a new passage:
Yesterday, i had to Cut some trees so i put on it the gasoline that i used for Ape....
What's happened?
The engine start with High smoke and The carburation was very clean.
I couldn't Cut anything!
So, i made a new fuel mix from another tank... surprise!
The engine run Very Good with out smoke and carburation perfect!
Now i think that the gas station sold me no only gasoline but a mix gasoline + diesel!!!!
- kjjohnson
- 1° Apista restauratore
- Messaggi: 6143
- Iscritto il: 3 dicembre 2007, 11:17
- Ape owned: MPR2
- Località: Bayfield, Ontario, Canada
- Contatta:
Re: rimontaggio motore Mp600 del 74
I never use old gasoline mix that arrives in any Ape. Often they have been sitting for a long time and there's water from condensation in the tank that causes big problems. I only use my own fuel mix that I keep separate. Always buy gasoline from a service station that sells a lot of gasoline. Ken
we buy/restore/sell P501 and P601s and parts/manuals/handbooks
http://www.kjjohnson.ca/
http://www.kjjohnson.ca/
-
- Apista apprendista
- Messaggi: 47
- Iscritto il: 16 novembre 2016, 0:47
- Ape owned: MPV2
Re: rimontaggio motore Mp600 del 74
Hi Ken!
The @pone has a wondeful sound now!! Fantastic!
The power is better than previous situation because I tuned the cylinder ports, very soft.
Question : What kind of the seal is used on the shaft of body "distributor contact breaker"?
I ask you this because I have a oil leak from the breaker and I want replace its seal.
I suppose that it damaged during the hell days when I tried to run the engine.
many thanks in advance
Pietro
The @pone has a wondeful sound now!! Fantastic!
The power is better than previous situation because I tuned the cylinder ports, very soft.
Question : What kind of the seal is used on the shaft of body "distributor contact breaker"?
I ask you this because I have a oil leak from the breaker and I want replace its seal.
I suppose that it damaged during the hell days when I tried to run the engine.
many thanks in advance
Pietro
- kjjohnson
- 1° Apista restauratore
- Messaggi: 6143
- Iscritto il: 3 dicembre 2007, 11:17
- Ape owned: MPR2
- Località: Bayfield, Ontario, Canada
- Contatta:
Re: rimontaggio motore Mp600 del 74
In the photo you can see where the 'O' ring sits up under the base of the distributor and not in the groove with the oil hole - Ken
we buy/restore/sell P501 and P601s and parts/manuals/handbooks
http://www.kjjohnson.ca/
http://www.kjjohnson.ca/
-
- Apista apprendista
- Messaggi: 47
- Iscritto il: 16 novembre 2016, 0:47
- Ape owned: MPV2
- kjjohnson
- 1° Apista restauratore
- Messaggi: 6143
- Iscritto il: 3 dicembre 2007, 11:17
- Ape owned: MPR2
- Località: Bayfield, Ontario, Canada
- Contatta:
Re: rimontaggio motore Mp600 del 74
the one in the photo? - Ken
we buy/restore/sell P501 and P601s and parts/manuals/handbooks
http://www.kjjohnson.ca/
http://www.kjjohnson.ca/
-
- Apista apprendista
- Messaggi: 47
- Iscritto il: 16 novembre 2016, 0:47
- Ape owned: MPV2
Re: rimontaggio motore Mp600 del 74
Yes!
Have you its dimensions?
Have you its dimensions?
- kjjohnson
- 1° Apista restauratore
- Messaggi: 6143
- Iscritto il: 3 dicembre 2007, 11:17
- Ape owned: MPR2
- Località: Bayfield, Ontario, Canada
- Contatta:
Re: rimontaggio motore Mp600 del 74
no, I don't have dimensions. You'll have to see a Dealer who might have old stock. I have lots of the original drive pins for the distributor but not for your model. They didn't come with that piece installed on them. Look on Ebay and use that part number and description - never know - Ken
we buy/restore/sell P501 and P601s and parts/manuals/handbooks
http://www.kjjohnson.ca/
http://www.kjjohnson.ca/
-
- Apista apprendista
- Messaggi: 47
- Iscritto il: 16 novembre 2016, 0:47
- Ape owned: MPV2
Re: rimontaggio motore Mp600 del 74
Hi Ken!
Today i replaced the rotary seal.
I tried, as your adviced me, to search on ebay with code piaggio.
I found the seal after one minute!
In your picture, you link the protezione of the seal for The pollution.
The dimensions is 10-18-4.it's made by NBR OR VITON. IT'S better the second choice.
It's An industrial spare parts made by many factory as skf, angst-pfister, trelleborg. ....
Today i replaced the rotary seal.
I tried, as your adviced me, to search on ebay with code piaggio.
I found the seal after one minute!
In your picture, you link the protezione of the seal for The pollution.
The dimensions is 10-18-4.it's made by NBR OR VITON. IT'S better the second choice.
It's An industrial spare parts made by many factory as skf, angst-pfister, trelleborg. ....
- kjjohnson
- 1° Apista restauratore
- Messaggi: 6143
- Iscritto il: 3 dicembre 2007, 11:17
- Ape owned: MPR2
- Località: Bayfield, Ontario, Canada
- Contatta:
Re: rimontaggio motore Mp600 del 74
happy you found it - Ken
we buy/restore/sell P501 and P601s and parts/manuals/handbooks
http://www.kjjohnson.ca/
http://www.kjjohnson.ca/