Buongiorno,
Ieri sera ho dovuto sistemare un guaio causato da un meccanico di cui mi ero fidato.
Gli diedi il motore quasi completamente smontato per sostituire i paraoli e i cuscinetti di banco prima di Natale.
Riconsegnato, a vista sembrava tutto bene.
Ma due giorni fa l'amara sorpresa : il trascinamento dell'alberino delle puntine era diventato stretto!
E non di decimi di mm, ma bensì UN millimetro.
Da 4 era diventato 3 mm.
Contattato il meccanico telefonicamente, mi disse che bisogna battere l'albero per farlo uscire e la sede si rovina facilmente.
Battere? Ho letto il manuale messo in rete da Ken ma non ho trovato nessuna indicazione di battere l'albero per farlo uscire.
Ho trovato tanti estrattori specifici, ma non a battente.
Dopo averlo sistemato, mi posso ancora fidare dell'albero? O è meglio cambiarlo quando ancora il motore è sul banco?
Grazie mille per i consigli in anticipo
smontaggio albero motore MP600 a martellate???
-
- Apista apprendista
- Messaggi: 47
- Iscritto il: 16 novembre 2016, 0:47
- Ape owned: MPV2
- kjjohnson
- 1° Apista restauratore
- Messaggi: 6148
- Iscritto il: 3 dicembre 2007, 11:17
- Ape owned: MPR2
- Località: Bayfield, Ontario, Canada
- Contatta:
Re: smontaggio albero motore MP600 a martellate???
Post some photos so we can see exactly the problem. If it's not right it needs fixing - Ken
Posta alcune foto in modo che possiamo vedere esattamente il problema. Se non è giusto che ha bisogno di fissaggio - Ken
Posta alcune foto in modo che possiamo vedere esattamente il problema. Se non è giusto che ha bisogno di fissaggio - Ken
we buy/restore/sell P501 and P601s and parts/manuals/handbooks
http://www.kjjohnson.ca/
http://www.kjjohnson.ca/
-
- Apista apprendista
- Messaggi: 47
- Iscritto il: 16 novembre 2016, 0:47
- Ape owned: MPV2
Re: smontaggio albero motore MP600 a martellate???
Okajama, I'll take some photos this evening.
The summary on English is:
The mechanical has used a hammer in order to disassembly the shaft from the crankcase or the inner of the bearing.
He knock the head of the shaft on the side of the clutch.
In the head there is a slope for the auxiliary shaft moves That moves the ignition.
The original dimension of the slope is 4 mm.
After is 3mm ...
Now, I was able to adjust the dimension but I have some doubt about the strenght of the thread after this stress.
He didn't use any special instrument from Piaggio.
Is it correct how he worked?
The summary on English is:
The mechanical has used a hammer in order to disassembly the shaft from the crankcase or the inner of the bearing.
He knock the head of the shaft on the side of the clutch.
In the head there is a slope for the auxiliary shaft moves That moves the ignition.
The original dimension of the slope is 4 mm.
After is 3mm ...
Now, I was able to adjust the dimension but I have some doubt about the strenght of the thread after this stress.
He didn't use any special instrument from Piaggio.
Is it correct how he worked?
- kjjohnson
- 1° Apista restauratore
- Messaggi: 6148
- Iscritto il: 3 dicembre 2007, 11:17
- Ape owned: MPR2
- Località: Bayfield, Ontario, Canada
- Contatta:
Re: smontaggio albero motore MP600 a martellate???
point out where the problem is. To remove the axle shaft it simply pulls out with hands. For bearing removal/replacement refer to the manual - or show me with a photo where the damage is - Ken -we buy/restore/sell P501 and P601s and parts/manuals/handbooks
http://www.kjjohnson.ca/
http://www.kjjohnson.ca/
-
- Apista apprendista
- Messaggi: 47
- Iscritto il: 16 novembre 2016, 0:47
- Ape owned: MPV2
Re: smontaggio albero motore MP600 a martellate???
Excuse me for delay response.
I've also problem with device for open the clutch.
Please look the picture Where it's showed the thread stressed.
I've also problem with device for open the clutch.
Please look the picture Where it's showed the thread stressed.
- kjjohnson
- 1° Apista restauratore
- Messaggi: 6148
- Iscritto il: 3 dicembre 2007, 11:17
- Ape owned: MPR2
- Località: Bayfield, Ontario, Canada
- Contatta:
Re: smontaggio albero motore MP600 a martellate???
Look at the photos, it will explain - I took these when restoring a 500MP so it's similar - Ken
complete file is here: - http://www.kjjohnson.ca/piaggio/APE%205 ... STORATION/ -
complete file is here: - http://www.kjjohnson.ca/piaggio/APE%205 ... STORATION/ -
we buy/restore/sell P501 and P601s and parts/manuals/handbooks
http://www.kjjohnson.ca/
http://www.kjjohnson.ca/