Ape MP 501 non parte

Quesiti tecnici riguardanti l'Ape anni '50, '60 e '70 (telai A, B, C, D, E, MP) / Technical questions about Ape in the fifties, sixties and seventies (A, B, C, D, E, MP chassis).
Rispondi
luigima76
Apista apprendista
Apista apprendista
Messaggi: 26
Iscritto il: 8 maggio 2010, 13:09

Ape MP 501 non parte

Messaggio da luigima76 »

Salve a tutti,
ho un'ape mp 501, l'ho utilizzata fino a 6 mesi fa ed andava benissimo fin quando per colpa della miscela errata ho grippato il motore. Ho fatto rifare la testata, ho sostituito il pistone, ho sostituito anche le puntine e il carburatore, erano tutti pezzi in pessime condizioni. RIMONTATO il tutto ogni tanto mi si accende pure ma poi si spegne dopo qualche secondo e no riparte più. il dubbio più grande che ho sono le puntine, E' POSSIBILE CHE NO LE ABBIA FASATE BENE??
vi prego aiutatemi
grazie a tutti luigi
Avatar utente
kjjohnson
1° Apista restauratore
1° Apista restauratore
Messaggi: 6141
Iscritto il: 3 dicembre 2007, 11:17
Ape owned: MPR2
Località: Bayfield, Ontario, Canada
Contatta:

Re: APE MP 501 NON PARTE

Messaggio da kjjohnson »

Luigi: Did you have the cylinder bored to the correct size for the new piston kit? Get yourself a compression tester and do a test and tell me what the reading is. Did you also reset the timing and check the point gap in the distributor? Go to my website and check out 'Vespacar P501 Motor Overhaul' for tips. - Ken
Photo0965.jpg
- [youtubecom]http://www.youtube.com/watch?v=VGmbliEz9g4[/youtubecom]
we buy/restore/sell P501 and P601s and parts/manuals/handbooks
http://www.kjjohnson.ca/
luigima76
Apista apprendista
Apista apprendista
Messaggi: 26
Iscritto il: 8 maggio 2010, 13:09

Re: Ape MP 501 non parte

Messaggio da luigima76 »

ciao,
grazie della risposta, oggi sono riuscito a far partire l'ape e a girarci per un ora,però sono senza marmitta di scarico e l'ape sembra camminare ingolfata cioè : quando accelero tirando le marci (cambiate) non fa quel rombo nitido che dovrebbe fare ma sfarfalla, PUO DIPENDERE DALLA MANCANZA DELLA MARMITTA??
SALUTI
LUIGI
Avatar utente
kjjohnson
1° Apista restauratore
1° Apista restauratore
Messaggi: 6141
Iscritto il: 3 dicembre 2007, 11:17
Ape owned: MPR2
Località: Bayfield, Ontario, Canada
Contatta:

Re: Ape MP 501 non parte

Messaggio da kjjohnson »

The lack of a muffler is not good but you haven't answered my question - Did you have the cylinder bored to the correct size for a new piston/rings kit? Can you tell me what the compression reading is? Was the cylinder scored badly? Ken
Photo0576.jpg
we buy/restore/sell P501 and P601s and parts/manuals/handbooks
http://www.kjjohnson.ca/
luigima76
Apista apprendista
Apista apprendista
Messaggi: 26
Iscritto il: 8 maggio 2010, 13:09

Re: Ape MP 501 non parte

Messaggio da luigima76 »

ciao,
il pistone e il cilindro sono ok, face ok tutto o, la misura della compressione non l'ho fatta perchè non ho gli strumenti, ma la compressione c'è, potrebbe essere oltre alla marmitta un fatto di carburazione o errata fasatura delle puntine? io ho regolato le puntine con il metodo della lampadina, va bene??
ciao e grazie
Avatar utente
kjjohnson
1° Apista restauratore
1° Apista restauratore
Messaggi: 6141
Iscritto il: 3 dicembre 2007, 11:17
Ape owned: MPR2
Località: Bayfield, Ontario, Canada
Contatta:

Re: Ape MP 501 non parte

Messaggio da kjjohnson »

Hard to say without a compression test. However, screw the mixture screw all the way IN and then unscrew it 2 1/2turns. Did you set the points at TDC? (top dead center). You can make minor adjustments to the timing by using the slide bolt on the distributor. Take a picture of it so I can see the current setting. You can find all this in the photo file 'Clutch Overhaul' on my website - Ken
007 timing adjustment slide .jpg
077 Finding TDC – rod must go through the.jpg
we buy/restore/sell P501 and P601s and parts/manuals/handbooks
http://www.kjjohnson.ca/
Avatar utente
Bestiol1
Apista aspirante
Messaggi: 22
Iscritto il: 6 ottobre 2008, 13:53

Re: Ape MP 501 non parte

Messaggio da Bestiol1 »

continuo il thread già iniziato ponendo un altro quesito. Ho una MP 501, che è andata benissimo per gli ultimi 12.000km. adesso mentre vado, a caldo a velocità costante, la sento un po' mancare, poi di punto in bianco mi scoppietta dallo scarico, perde potenza e, inesorabilemente, si ferma. ho pensato potessero essere le puntine o il conensatore, le ho cambiate ma nulla, dopo circa 10-11 km a velocità quasi costante di 50 km/h, nell'apri chiudi, fa le bizze cercado di spegnersi. hoprovato, al minimo, a muovere il carburatore, qualora fosse il vulcanizzato che lo sorregge crepato ma niente, nessuna variazione di giri.... ?:;
Qualcuno ha qualche idea? inizio a pensare ch eun Ape di 30 anni non sopporti 10.000 km/anno e che debba iniziare a pensare ad una classic nuova... :((

Grazie in anticipo per le risposte
B1
Avatar utente
kjjohnson
1° Apista restauratore
1° Apista restauratore
Messaggi: 6141
Iscritto il: 3 dicembre 2007, 11:17
Ape owned: MPR2
Località: Bayfield, Ontario, Canada
Contatta:

Re: Ape MP 501 non parte

Messaggio da kjjohnson »

Get yourself a compression tester and take a reading and post a photo of it. I believe your problem is worn piston rings and lack of compression. The tester will tell me what I need to know. If it's the original piston and rings get yourself one size larger replacement piston kit, have the cylinder honed to fit, clean the carbon from the exhaust port, set the timing and you should be good to go. Go to my website and look at this file. - Ken - http://www.kjjohnson.ca/piaggio/VESPACA ... 0OVERHAUL/ -
0149.jpg
we buy/restore/sell P501 and P601s and parts/manuals/handbooks
http://www.kjjohnson.ca/
leonardo26
Apista aspirante
Messaggi: 12
Iscritto il: 1 luglio 2011, 22:29
Ape owned: MPR1

Re: Ape MP 501 non parte

Messaggio da leonardo26 »

Bestiol1 ha scritto:continuo il thread già iniziato ponendo un altro quesito. Ho una MP 501, che è andata benissimo per gli ultimi 12.000km. adesso mentre vado, a caldo a velocità costante, la sento un po' mancare, poi di punto in bianco mi scoppietta dallo scarico, perde potenza e, inesorabilemente, si ferma. ho pensato potessero essere le puntine o il conensatore, le ho cambiate ma nulla, dopo circa 10-11 km a velocità quasi costante di 50 km/h, nell'apri chiudi, fa le bizze cercado di spegnersi. hoprovato, al minimo, a muovere il carburatore, qualora fosse il vulcanizzato che lo sorregge crepato ma niente, nessuna variazione di giri.... ?:;
Qualcuno ha qualche idea? inizio a pensare ch eun Ape di 30 anni non sopporti 10.000 km/anno e che debba iniziare a pensare ad una classic nuova... :((

Grazie in anticipo per le risposte
B1

Non perdere tempo, cambia il serbatoio, tuo stesso problema son diventato matto.....
Non riesco ad allegarti le foto in questo momento ma vedere quanta ruggine c'era mi son preso paura.
leonardo26
Apista aspirante
Messaggi: 12
Iscritto il: 1 luglio 2011, 22:29
Ape owned: MPR1

Re: Ape MP 501 non parte

Messaggio da leonardo26 »

Qui era già ripulito, ma in zona manicotto dell rubinetto, sotto la lameriera che vedi piegata in foto è un macello.

Sono in ballo per rifarlo in inox o farlo ri-zincare e richiudere.

Ciao Leo.
Ultima modifica di leonardo26 il 22 settembre 2012, 13:33, modificato 2 volte in totale.
Avatar utente
kjjohnson
1° Apista restauratore
1° Apista restauratore
Messaggi: 6141
Iscritto il: 3 dicembre 2007, 11:17
Ape owned: MPR2
Località: Bayfield, Ontario, Canada
Contatta:

Re: Ape MP 501 non parte

Messaggio da kjjohnson »

upload photos from your own computer, don't bother with ImageShack - Ken

caricare le foto dal proprio computer, non preoccupatevi di ImageShack - Ken
we buy/restore/sell P501 and P601s and parts/manuals/handbooks
http://www.kjjohnson.ca/
Michelangelo
Apista aspirante
Messaggi: 1
Iscritto il: 29 marzo 2021, 22:03

Re: Ape MP 501 non parte

Messaggio da Michelangelo »

Ciao sono nuovo sul forum . Ho un ape 501 perché quando tiro la frizione l ape tenta a spegnersi ?????
Avatar utente
kjjohnson
1° Apista restauratore
1° Apista restauratore
Messaggi: 6141
Iscritto il: 3 dicembre 2007, 11:17
Ape owned: MPR2
Località: Bayfield, Ontario, Canada
Contatta:

Re: Ape MP 501 non parte

Messaggio da kjjohnson »

Michelangelo: È meglio che tu apra un nuovo file così possiamo aiutarti. Un breve video sarebbe di grande aiuto - Ken - Best you open a new file so we can help you. A short video would be of great assistance ^&$
we buy/restore/sell P501 and P601s and parts/manuals/handbooks
http://www.kjjohnson.ca/
Rispondi