Api di Ken

Inserisci le foto e le informazioni del tuo motoveicolo d'epoca (solo anni '50, '60 e '70) / Add you vehicle's photos and info ('50, '60 and '70 only)
Avatar utente
kjjohnson
1° Apista restauratore
1° Apista restauratore
Messaggi: 6141
Iscritto il: 3 dicembre 2007, 11:17
Ape owned: MPR2
Località: Bayfield, Ontario, Canada
Contatta:

Re: Api di Ken

Messaggio da kjjohnson »

Perhaps I will condense and make a file for use by whoever wishes to assume this task - The problem was made more difficult as there were very few km's on the Ape so little clearance from wear between the piston and the cylinder. It was so tight that even diesel fuel poured on top of the piston wouldn't pass between them to lubricate and ease the strain of removal. If the rings had been worn with use there would have been clearance. If the motor hadn't been exposed to such moisture and oil sprayed in the spark plug hole it would have been relatively easy. Not so. - Ken
-
Forse potrò condensare e creare un file da utilizzare da chiunque desideri assumere questo compito. Il problema è stato reso più difficile dal momento che in Ape c'erano pochissimi km di distanza dall'usura tra il pistone e il cilindro. Era talmente stretto che persino il carburante diesel versato sopra il pistone non passava tra loro per lubrificare e alleviare lo sforzo di rimozione. Se gli anelli fossero stati indossati con l'uso ci sarebbe stato spazio. Se il motore non fosse stato esposto a tale umidità e l'olio spruzzato nel foro della candela sarebbe stato relativamente facile. Non così. - Ken 5/%
we buy/restore/sell P501 and P601s and parts/manuals/handbooks
http://www.kjjohnson.ca/
Avatar utente
kjjohnson
1° Apista restauratore
1° Apista restauratore
Messaggi: 6141
Iscritto il: 3 dicembre 2007, 11:17
Ape owned: MPR2
Località: Bayfield, Ontario, Canada
Contatta:

Re: Api di Ken

Messaggio da kjjohnson »

POLICE APE AD1T L() ^&$ Too many photos to upload - go to my website - Ken
IMG_20190302_122519.jpg
IMG_20190302_125524.jpg
IMG_20190302_144527.jpg
IMG_20190302_144721.jpg
IMG_20190302_150414.jpg
^&$ ^&$
- https://www.kjjohnson.ca/piaggio/POLICE%20APE%20AD1T/ -
we buy/restore/sell P501 and P601s and parts/manuals/handbooks
http://www.kjjohnson.ca/
Avatar utente
kjjohnson
1° Apista restauratore
1° Apista restauratore
Messaggi: 6141
Iscritto il: 3 dicembre 2007, 11:17
Ape owned: MPR2
Località: Bayfield, Ontario, Canada
Contatta:

Re: Api di Ken

Messaggio da kjjohnson »

POLICE APE AD1T L() ^&$ 21 more photos - engine casings apart now. - Ken
IMG_20190303_101442.jpg
- https://www.kjjohnson.ca/piaggio/POLICE%20APE%20AD1T/ - ^&$ ^&$
IMG_20190304_102906.jpg
we buy/restore/sell P501 and P601s and parts/manuals/handbooks
http://www.kjjohnson.ca/
Avatar utente
kjjohnson
1° Apista restauratore
1° Apista restauratore
Messaggi: 6141
Iscritto il: 3 dicembre 2007, 11:17
Ape owned: MPR2
Località: Bayfield, Ontario, Canada
Contatta:

Re: Api di Ken

Messaggio da kjjohnson »

A crate of things from mate in UK - Ken
IMG_20190304_130358.jpg
IMG_20190304_131909.jpg
IMG_20190304_143247.jpg
:D
IMG_20190305_103440.jpg
motore 190cc (spinotto 18mm pistone 63mm) P601V L.S. (G.B.) carburatore DellOrto SHB27/20A - year ?
IMG_20190306_154833.jpg
IMG_20190311_151834.jpg
IMG_20190311_151931.jpg
IMG_20190311_170825.jpg
Ultima modifica di kjjohnson il 12 marzo 2019, 11:37, modificato 4 volte in totale.
we buy/restore/sell P501 and P601s and parts/manuals/handbooks
http://www.kjjohnson.ca/
Avatar utente
kjjohnson
1° Apista restauratore
1° Apista restauratore
Messaggi: 6141
Iscritto il: 3 dicembre 2007, 11:17
Ape owned: MPR2
Località: Bayfield, Ontario, Canada
Contatta:

Re: Api di Ken

Messaggio da kjjohnson »

APE BUBBLY - going to have a new look - Ken
IMG-20161030-01700.jpg
IMG_20190226_155052.jpg
IMG_20190307_143346.jpg
IMG_20190307_143406.jpg
IMG_20190307_143431.jpg
we buy/restore/sell P501 and P601s and parts/manuals/handbooks
http://www.kjjohnson.ca/
Avatar utente
kjjohnson
1° Apista restauratore
1° Apista restauratore
Messaggi: 6141
Iscritto il: 3 dicembre 2007, 11:17
Ape owned: MPR2
Località: Bayfield, Ontario, Canada
Contatta:

Re: Api di Ken

Messaggio da kjjohnson »

we buy/restore/sell P501 and P601s and parts/manuals/handbooks
http://www.kjjohnson.ca/
Avatar utente
kjjohnson
1° Apista restauratore
1° Apista restauratore
Messaggi: 6141
Iscritto il: 3 dicembre 2007, 11:17
Ape owned: MPR2
Località: Bayfield, Ontario, Canada
Contatta:

Re: Api di Ken

Messaggio da kjjohnson »

POLICE APE AD1T - pistone originale - 60mm Ken ^&$
IMG_20190302_125540.jpg
IMG_20190309_143511.jpg
IMG_20190309_143522.jpg
IMG_20190309_143549.jpg
^&$ ^&$
Ultima modifica di kjjohnson il 10 marzo 2019, 20:04, modificato 1 volta in totale.
we buy/restore/sell P501 and P601s and parts/manuals/handbooks
http://www.kjjohnson.ca/
pitt
Apista veterano
Apista veterano
Messaggi: 374
Iscritto il: 11 ottobre 2011, 21:16
Ape owned: AC4

Re: Api di Ken

Messaggio da pitt »

con che cosa hai pulito il pistone?
with what did you clean the piston?
Avatar utente
kjjohnson
1° Apista restauratore
1° Apista restauratore
Messaggi: 6141
Iscritto il: 3 dicembre 2007, 11:17
Ape owned: MPR2
Località: Bayfield, Ontario, Canada
Contatta:

Re: Api di Ken

Messaggio da kjjohnson »

A very light cleaning in a media blaster with fine sand on exterior surfaces only. Spinotto undamaged. Razor blade along edges of the piston rings to free solids. A light honing of the cylinder with test for proper clearance at a local automotive specialty shop that does my cylinder/piston work is all I believe is needed. Good cleaning should free the rings for movement. With luck I will be able to use both and re-install as the needle bearing on the wrist pin wasn't damaged but I have a replacement if required ( #llll ). Might be my lucky day! - Ken
- [-O<
Una pulizia molto leggera in un media blaster con sabbia fine solo su superfici esterne. Spinotto integro. Lama di rasoio lungo i bordi dei segmenti del pistone per liberare i solidi. Una leggera levigatura del cilindro con test per l'autorizzazione corretta in un negozio di specialità automobilistiche locale che fa il mio lavoro cilindro / pistone è tutto ciò che ritengo sia necessario. Una buona pulizia dovrebbe liberare gli anelli per il movimento. Con un po 'di fortuna potrò usare entrambi e reinstallare quando il cuscinetto dell'ago sul perno da polso non è danneggiato, ma ho una sostituzione se necessario (#llll). Potrebbe essere il mio giorno fortunato! - Ken ^&$
p601 1090 media blaster.jpg
Nut Buster
IMG_20190310_155441.jpg
- https://www.kjjohnson.ca/piaggio/POLICE%20APE%20AD1T/ - ^&$
we buy/restore/sell P501 and P601s and parts/manuals/handbooks
http://www.kjjohnson.ca/
Avatar utente
kjjohnson
1° Apista restauratore
1° Apista restauratore
Messaggi: 6141
Iscritto il: 3 dicembre 2007, 11:17
Ape owned: MPR2
Località: Bayfield, Ontario, Canada
Contatta:

Re: Api di Ken

Messaggio da kjjohnson »

190cc motore P601V U.K. L()
IMG_20190312_082947.jpg
IMG_20190312_092219.jpg
IMG_20190312_093606.jpg
IMG_20190312_100243.jpg
IMG_20190312_102710.jpg
IMG_20190312_135609.jpg
IMG_20190312_142257.jpg
IMG_20190312_161532.jpg
we buy/restore/sell P501 and P601s and parts/manuals/handbooks
http://www.kjjohnson.ca/
Avatar utente
kjjohnson
1° Apista restauratore
1° Apista restauratore
Messaggi: 6141
Iscritto il: 3 dicembre 2007, 11:17
Ape owned: MPR2
Località: Bayfield, Ontario, Canada
Contatta:

Re: Api di Ken

Messaggio da kjjohnson »

190cc motore P601V U.K. L()
IMG_20190314_070752.jpg
IMG_20190314_100010.jpg
IMG_20190314_123835.jpg
IMG_20190314_140441.jpg
IMG_20190314_154224.jpg
-
Diverso coperchio frizioni ? Series 1 and Series 2 ?
IMG_20190314_154754.jpg
IMG_20190315_140411.jpg
IMG_20190315_140441.jpg
we buy/restore/sell P501 and P601s and parts/manuals/handbooks
http://www.kjjohnson.ca/
Avatar utente
kjjohnson
1° Apista restauratore
1° Apista restauratore
Messaggi: 6141
Iscritto il: 3 dicembre 2007, 11:17
Ape owned: MPR2
Località: Bayfield, Ontario, Canada
Contatta:

Re: Api di Ken

Messaggio da kjjohnson »

CYNTHIA A PROSECCO APE Shipping soon to clients - Ken
IMG_20190320_072457.jpg
IMG_20190320_110453.jpg
IMG_20190320_110528.jpg
IMG_20190320_110604.jpg
IMG_20190320_110619.jpg
IMG_20190321_080858.jpg
- https://www.kjjohnson.ca/piaggio/CYNTHI ... CCO%20APE/ -
IMG_20190322_090715.jpg
we buy/restore/sell P501 and P601s and parts/manuals/handbooks
http://www.kjjohnson.ca/
Avatar utente
kjjohnson
1° Apista restauratore
1° Apista restauratore
Messaggi: 6141
Iscritto il: 3 dicembre 2007, 11:17
Ape owned: MPR2
Località: Bayfield, Ontario, Canada
Contatta:

Re: Api di Ken

Messaggio da kjjohnson »

Motore P601 L.S. electronic ignition 190cc - before I start this on my test stand I need some assistance from those with more 'electronic ignition' experience - Ken S;: prima di iniziare questo sul mio banco di prova ho bisogno di assistenza da parte di chi ha più esperienza di "accensione elettronica"
164961 P601 bobine pre May 82.jpg
IMG_20190324_095010.jpg
Electrics - P601 L.S..jpg
The red/pink wire from the 'bobina' goes to terminal 15 on the ignition switch. Can you explain it's purpose? Il cavo rosso / rosa della "bobina" va al terminale 15 dell'interruttore di accensione. Puoi spiegare il suo scopo?
IMG_20190326_101419.jpg
we buy/restore/sell P501 and P601s and parts/manuals/handbooks
http://www.kjjohnson.ca/
Avatar utente
martincontrol
Esperto TM P703
Esperto TM P703
Messaggi: 543
Iscritto il: 28 marzo 2014, 15:09
Ape owned: MPR1

Re: Api di Ken

Messaggio da martincontrol »

Penso che il filo rosa che arriva alla chiave, serva per spegnere il motore, porta a massa (-) la bobina, così si spegne il motore.
Avatar utente
kjjohnson
1° Apista restauratore
1° Apista restauratore
Messaggi: 6141
Iscritto il: 3 dicembre 2007, 11:17
Ape owned: MPR2
Località: Bayfield, Ontario, Canada
Contatta:

Re: Api di Ken

Messaggio da kjjohnson »

I agree. The Service Station Manual that I have explains it so I've hooked up an ignition switch onto my test stand in the same manner.
I have several extra coils to test as well as several extra 'centralina' but first I need an Ohm meter for testing electrical output while the motor is on the test stand.
First of all I have to figure out why the L.S. pump isn't working properly. Although I cleaned it oil isn't pumping through the line to the engine.
co:;
Sono d'accordo. Il manuale della stazione di servizio che ho spiegato così ho collegato un interruttore di accensione sul mio banco di prova nello stesso modo.
Ho diverse bobine extra da testare e diversi extra "centralina", ma prima ho bisogno di un misuratore Ohm per testare l'uscita elettrica mentre il motore è sul banco di prova.
Prima di tutto devo capire perché la L.S. la pompa non funziona correttamente. Anche se l'ho pulito, l'olio non sta pompando attraverso la linea verso il motore.
IMG_20190327_112929.jpg
we buy/restore/sell P501 and P601s and parts/manuals/handbooks
http://www.kjjohnson.ca/
Rispondi